3009-02 Elastico Plus UV 2K

It is extra elastic, UV resistant waterproofing and concrete protection mortar that forms an effective barrier against salts, can be applied indoors and outdoors, consisting of emulsion polymer based liquid component, cement based powder component containing chemical additives that increase water impermeability and workability.

► Cement and Acrylic Based
► Fully Elastic
► Two Component
► For Waterproofing Purposes
► Easy to Apply
► Low Consumption

> White
> Public Works Pos No:


• It is used; Indoors-outdoors, vertical and horizontal applications from the direction of water,
• In basic insulation,
• In retaining walls,
• On floors that are thought to make deflection,
• On terraces (can be used under light load without protection.)
• In wet areas such as WC, bathroom, kitchen and balcony,
• In wwimming pools,
• In drinking and utility water tanks,
• In facilities such as hot springs and Turkish baths,
• In sea water channels,
• Where waterproofing and protection against salty water is required,
• Protection of concrete surfaces against carbonation and chlorine attacks,
• Walking paths of marinas,
• For insulation of flower heads.
• In areas where UV resistance is required.
• 3009-02 Elastico Plus UV 2K with a thickness of 1 mm provides equivalent protection to concrete over 80 cm against carbonation.
• Waterproof, resistant to positive water pressure of 7 bar.
• Has excellent adhesion properties.
• Easy to prepare and apply.
• It is applied with brush and spraying machine.
• Long working time.
• Resistant to UV rays.
• Suitable for light pedestrian traffic.
• Water vapor permeable.
• High durability.
• Resistant to freeze-thaw cycle.
• High resistance to carbon dioxide and chlorine ions.
• While a curing time of 7-28 days is required for conventional waterproofing materials, it can be applied to a fresh concrete of 24 hours.
• It can be used safely in drinking water tanks.

a) Surface Preparation:
It should be ensured that the cement-based surfaces in contact with water are solid, dry, carrier, dust-free and clean and at the same time in balance. The surface should be thoroughly cleaned of any oil, grease, rust and paraffin residues that may weaken the adherence and there should be no loose particles on the surface. Iron and wooden wedges on the surface should be removed and if any, active water leakages and gaps should be filled with Lotti Sealant Mortar or Structural Repair Mortar, and corners and edges should be chamfered at least 4 cm radius. Application surface is wet and wait until the application surface is wet and dry/wet. If the coating material loses water immediately and becomes matt, it is understood that the surface is not sufficiently wetted or dries quickly. In such cases, when the air is hot or the materials remain in the wind, only 10% of component B can be added to the mixed material for the first layer.

b) Product Preparation:
Liquid component B (3009-0 Elastico Plus UV 2K) is poured into a clean application bucket and powder component A (3009 Elastico Plus UV 2K) is added slowly and they are mixed with a 400-600 rpm mixer for 3-5 minutes until a homogenous and lump-free mixture is obtained. After resting for 3-5 minutes and mixing again for 30 seconds, the material is ready for use.

c) Application Method:
Prepared 3009-02 Elastico Plus UV 2K mixture is applied in two or three layers with the help of a Thoro brush. The direction of brush application on each layer should be perpendicular to each other. Waiting time between coats varies according to ambient conditions.


There are no reviews yet.

Be the first to review “3009-02 Elastico Plus UV 2K”

Your email address will not be published. Required fields are marked *

    Lotti Building Chemicals which includes a total of 58 products under three main product categories, it is aimed to make a significant contribution to the process of brandization in Turkey as well as in abroad countries through offering of epoxy and polyurethane systems, ceramic adhesives, joint fillers and maintenance products, and outer façade insulation materials.


    Altıntepe Mh. E. Bagdat Cd. No:19/1 Istanbul/Turkey